Services: Electrical testing and certification, environmental or chemical testing

The EU Regulation on Plastics in Contact with Food has added four new substances allowed for use, which will come into effect on November 18, 2026


Time:

2026-11-17

The European Union has issued (EU) 2026/2412, amending Annex I of the EU Regulation on Plastic Food Contact Materials, adding four new substances allowed for use, which will come into effect on November 18, 2026.

On October 29, 2026, the European Commission published (EU) 2026/2412, amending Annex I to Regulation (EU) No 10/2011 on plastic materials and articles intended to come into contact with food (i.e., the EU Plastic Food Contact Materials Regulation), adding 4 substances authorized for use. This amending Regulation entered into force on November 18, 2026. Meanwhile, two verification of conformity notes were added to Table 3 of Point 3 in Annex I.

 

 

 

 

Add 4 new permitted substances

 

Chopped carbon fibres, from carbonised polyacrylonitrile 

FCM number: 1086

Restrictive requirements:

1. Used as an additive or polymer processing aid: Yes

2. Used as a monomer or other starting material or polymer obtained by microbial fermentation: No

3. Applicable FRF: No

4. Restrictions and specifications: Only for use in polyetheretherketone (PEEK) polymers, at a concentration not exceeding 40% w/w. Fibers must be made of polyacrylonitrile, with a minimum carbon content of 95% w/w, and any dimension must not be on the nanoscale (diameter > 100 nm).

 

Nano precipitated calcium carbonate, uncoated

FCM number: 1087

Restrictive requirements:

1. Used as an additive or polymer production aid: Yes

2. Used as a monomer or other starting material or polymer obtained by microbial fermentation: No

3. Applicable FRF: No

4. Restrictions and specifications: Shall not be used in the manufacture of materials and articles intended to come into contact with infant formula (7).

5. Notes on conformity verification (32): When in contact with acidic foods, there is a risk that the overall migration limit (OML) may be exceeded.

 

Poly(2-hydroxypropanoic acid), n-octyl/n-decyl esters

FCM number: 1088

Restrictions:

1. Used as an additive or polymer processing aid: Yes

2. Used as a monomer or other starting substance or polymer obtained by microbial fermentation: No

3. Applicable FRF: No

4. SML: 0.05 mg/kg

5. Restrictions and specifications: May only be used as an additive in materials and articles made of polylactic acid (PLA), with a dosage not exceeding 15% w/w; such materials and articles shall not contain starch (FCM substance number 564), nor shall they contain other additives with a similar function to starch that may increase the migration amount; intended for food contact with water included in food category 01.01, or foods included in food categories 04.01 (fresh or chilled fruit), 04.04 (fresh or chilled vegetables) and 08.01 (vinegar) listed in Table 2 of Annex III, under conditions of temperature not exceeding 40°C and time not exceeding 10 days.

6. Note on verification of compliance (33): When using food simulants other than food simulant B, there is a risk that the specific migration limit (SML) may be exceeded.

 

Mixture of 1,9-nonanediamine (NMDA) and 2-methyl-1,8-octanediamine (MODA)

FCM No.: 1089

Restrictions:

1. Used as an additive or polymer production aid: No

2. Used as a monomer or other starting material or polymer obtained by microbial fermentation: Yes

3. Applicable FRF: No

4. SML: 0.05 mg/kg

5. Restrictions and specifications: May only be used as a comonomer copolymerized with terephthalic acid, for the manufacture of polyamide materials and articles. It shall not be used in the manufacture of materials and articles intended to come into contact with infant formula (7) and breast milk. The migration of components composed of NMDA/MODA-related substances with a molecular weight below 1000 Da shall not exceed 5 mg/kg of food.

 

This update is the revision of the EU Plastics Regulation Positive List, effective on November 18, 2026. Products exported to the EU should comply with the compliance requirements of the latest positive list, and special attention must be paid to the restrictive requirements and conformity verification notes of the newly added substances.

 

As a professional third-party testing and technical service institution, Jiayu Testing possesses qualifications such as CMA, CNAS, CPSC, and CCC, and is simultaneously recognized by laboratories of multiple authoritative certification bodies at home and abroad. It has a professional testing technical team, is equipped with advanced instruments and equipment, and is proficient in various regulatory standards. It professionally provides food contact material (FCM) testing services for various materials (such as coatings, silicone rubber, plastics, metals, glass-ceramic enamel, bamboo and wood, paper and cardboard, etc.) in China, the United States, the European Union and its member states (France, Italy, Germany, etc.), Japan, South Korea, and other countries, ensuring that your products comply with the regulatory requirements of various countries. You are welcome to contact us at 400-9269-886!

手机官网
手机官网

Wechat Public

Account